GMS:GAGE Package

From XMS Wiki
Revision as of 16:45, 23 May 2022 by Klemon (talk | contribs)
Jump to navigationJump to search
MODFLOW
Pre-processing
MODFLOW Commands
Building a MODFLOW Model
Map to MODFLOW
Calibration
Packages Supported in GMS
Saving a MODFLOW Simulation
Importing MODFLOW Files
Unsupported MODFLOW Features
Run MODFLOW
Post-processing
MODFLOW Display Options
MODFLOW Post-Processing Viewing Options
Reading a MODFLOW Simulation
Tutorials
Packages
Flow: BCF6, HUF, LPF, UPW
Solvers:

DE4, GMG, NWT, PCG,

PCGN, LMG, SIP, SOR,

SMS
Other:

BAS6, BFH, CHD1, CLN,

DRN1, DRT1, EVT1, ETS1,

GAGE, GHB1, GNC, HFB1,

HUF, LAK3, MNW1, MNW2,

OUT1, RCH1, RIV1, SFR2,

STR1, SUB1, SWI2, WEL1,

UZF1

The MODFLOW Gage (GAGE) package allows gaging stations to be added to lakes and SFR stream reaches. A gaging station provides detailed time series data. MODFLOW generates a text file for each GAGE station that is available to be opened from a MODFLOW solution in the Project Explorer. The GAGE package is available in the GAGE Tutorial. GMS also provides an interface to generate gage plots via the Plot Wizard. A detailed description of the GAGE input is available at the USGS website.

GAGE Package Dialog

Gaging stations can be directly added via the GAGE Package dialog. Stream gages are added in the table at the top using the SFR segment and reach for the desired cell. Lake gages are added in the table at the bottom using the lake ID. A button is also provided to easily add gage stations for all lakes in the model. The OUTTYPE column for both lakes and streams determines the data columns included in the text output.

The OUTTYPE options for SFR streams include:

0 – Default values including time, stage, outflow, and solute concentration.
1 – Default values plus depth, width, and flow at midpoint.
2 – Default values plus streambed conductance for the reach, head difference across streambed, and hydraulic gradient across streambed.
3 – Default values plus solute load in stream (if GWT is active).
4 – All of the above.
5 – Use for diversions to provide a listing of time, stage, flow diverted, maximum assigned diversion rate, flow at end of upstream segment prior to diversion, solute concentration, and solute load.
6 – Used for unsaturated flow routing to provide a listing of time, stage, ground-water head, streambed seepage, change in unsaturated storage, and recharge.
7 – Used for unsaturated flow routing to provide a listing of time and the unsaturated water content profile beneath the stream. Two profiles are printed. The first is the volume average water content of ISUZN unsaturated cells beneath a stream reach. The second profile is the volume averaged water content beneath the low flow channel only. If ISUZN =1 then both water content profiles will be the same.
8 – This is used for unsaturated flow to provide a listing of time and the following budget components summed over all stream reaches: stream loss; stream gain; infiltration into the unsaturated zone; change of storage in the unsaturated zone; recharge; and storage in the unsaturated zone.

The OUTTYPE for lakes include:

0 – Default values including time, stage, volume, and concentration.
1 – Default values plus all inflows to and outflows from lake (as volumes during time increment), and total lake conductance.
2 – Default values plus changes in lake stage, lake volume, and solute concentrations.
3 – All of the above except time-step budget error.
4 – Time, lake, stage, etc.
The GAGE Package dialog