SMS:RMA2 Material Properties: Difference between revisions

From XMS Wiki
Jump to navigationJump to search
Line 2: Line 2:


=== Turbulence ===
=== Turbulence ===
[[Image:RMA2 MP Turbulence.jpg|thumb|400 px|''RMA2 Material Properties'' showing the ''Turbulence'' tab]]
[[Image:RMA2 MP Turbulence.png|thumb|450 px|''RMA2 Material Properties'' showing the ''Turbulence'' tab]]
The global turbulence values (specified in the [[SMS:RMA2 Model Control Dialog|RMA2 Model Control]]) can be overridden for each material.
The global turbulence values (specified in the [[SMS:RMA2 Model Control Dialog|RMA2 Model Control]]) can be overridden for each material.
* Standard eddy viscosity method
* Standard eddy viscosity method

Revision as of 15:40, 23 July 2019

The RMA2 Material Properties dialog is reached through the RMA2 | Material Properties menu command. For an in depth discussion of the RMA2 material properties, consult the RMA2 Users Guide. [1] [2]

Turbulence

RMA2 Material Properties showing the Turbulence tab

The global turbulence values (specified in the RMA2 Model Control) can be overridden for each material.

  • Standard eddy viscosity method
    • Exx – The x-momentum of turbulent exchange in the x-direction (lb-sec/ft2 or Pascal-sec for SI-units)
    • Exy – The x-momentum of turbulent exchange in the y-direction (lb-sec/ft2 or Pascal-sec for SI-units)
    • Eyx – The y-momentum of turbulent exchange in the x-direction (lb-sec/ft2 or Pascal-sec for SI-units)
    • Eyy – The y-momentum of turbulent exchange in the y-direction (lb-sec/ft2 or Pascal-sec for SI-units)
    • Note: 1 lb-sec/ft2 = 47.879 Pascal-sec
  • Smagorinski method
    • TBFACT – Smagorinsky coefficient for turbulent exchange. A negative value applies the default coefficient (0.05).
    • TBFACTS – Not applied in RMA2. Smagorinsky coefficient for diffusion (Vorticity). A negative value applies the default coefficient (0.05).
    • TBMINF – Smagorinsky minimum turbulent exchange factor. A negative value applies the default coefficient (1.0).
    • TBMINFS – Not applied in RMA2. Smagorinsky minimum diffusion (Vorticity) factor. A negative value applies the default coefficient (1.0).

Roughness

The global roughness value (specified in the RMA2 Model Control) can be overridden for each material. The material roughness can be specified as a single value, or depth dependent.

File:RMA2 MP Roughness.jpg
RMA2 Material Properties dialog showing the Roughness tab

Marsh porosity

File:RMA2 MP March.jpg
RMA2 Material Properties dialog showing the March Porosity tab

The global marsh porosity values (specified in the RMA2 Model Control) can be overridden for each material. Since wetting and drying cause abrupt changes to the shape of the finite element mesh, numerical stability problems can result when wetting and drying occurs. In an attempt to address the fact that wetting and drying is a continuous process, while the mesh is a discreet data set, marsh porosity was implemented for RMA2. When marsh porosity is used, elements are considered "dry" only if ALL nodes on the element are dry.

Abrupt changes in the marsh porosity parameters between adjacent node can lead to divergence. The results from a simulation using marsh porosity can be difficult to interpret due to the fact that partly dry marsh elements appear completely wet even thought the water surface elevation is lower than part of the element.

Marsh porosity is only available when running a dynamic RMA2 simulation.

Wind

According to the RMA2 model documentation, "Because of lack of experience in using storms in a simulation, this feature remains experimental."

Wind shear stress at the water surface is caused by friction between the moving air and water. The shear stress coefficient is a function of wind speed. The global wind values (specified in the RMA2 Model Control) can be overridden for each material.

Wind parameters are only available when running a dynamic RMA2 simulation.

File:RMA2 MP Wind.jpg
RMA2 Material Properties showing the Wind tab

Rainfall

File:RMA2 MP Rainfall.jpg
RMA2 Material Properties showing the Rainfall tab

The global rainfall and evaporation values (specified in the RMA2 Model Control) can be overridden for each material.

Coriolis

The global coriolis values (specified in the RMA2 Model Control) can be overridden for each material.

File:RMA2 MP Coriolis.jpg
RMA2 Material Properties dialog showing the Coriolis tab

Related Topics

RMA2