WMS:GSSHA Feature Nodes: Difference between revisions

From XMS Wiki
Jump to navigationJump to search
No edit summary
(No difference)

Revision as of 17:15, 29 December 2008

The Coverage Properties dialog is where the attributes associated with feature points/nodes on the GSSHA coverage are defined. WMS automatically assigns the correct type (generic, link break, or junction) to each point/node based on the type of feature arcs connected to the node, although the point/node type is not displayed in this dialog. It is possible to change the feature type attributes that are displayed in the table, select whether to show attributes for all features or just the selected features, and to filter the data shown in the table based on specific attribute values.

GsshaNodeAtts.jpg

GSSHA Feature Node Properties

Link

The link number is assigned by WMS to nodes that have hydraulic structures defined.

Hydraulic Structures

Click on the Hydraulic structures button to define hydraulic structures which exist in the GSSHA stream network. Link-break type nodes on GSSHA stream arcs (trapezoidal or cross-section) are used for defining known points of control and modification of the stream flow by in-stream hydraulic structures such as weirs and culverts. Hydraulic structures are represented as a separate link in the stream network in GSSHA. As such, if a feature node does not exist where a hydraulic structure exists, a feature node (with the link-break type) must be placed there.

There are three main types of hydraulic structures: weirs, culverts, and implicit defined structures. Any number of weirs, culverts, and/or curves may be specified together, but with only one instance of each curve type allowed.

Weirs
  • Horizontal Broad-Crested
  • Infinite Sag Vertical Curve

Parameters for a Horizontal Broad-crested Weir: crest length, discharge coefficient (forward flow), discharge coefficient (reverse flow), crest low point elevation

Parameters for a Infinite Sag Vertical Curve: left slope, right slope, discharge coefficient (forward flow), discharge coefficient (reverse flow), crest low point elevation

Culverts
  • Round
  • Oval
  • Rectangular

Parameters for Round Culverts: diameter, upstream invert, downstream invert, inlet loss coefficient, reverse flow inlet loss coefficient, slope, length, Manning's n value

Parameters for Oval Culverts: axis width, axis height, upstream invert, downstream invert, inlet loss coefficient, reverse flow inlet loss coefficient, slope, length, Manning's n value

Parameters for Rectangular Culverts: box width, box height, upstream invert, downstream invert, inlet loss coefficient, reverse flow inlet loss coefficient, slope, length, Manning's n value

Hydraulic Structure Curves

A hydraulic structure can be implicitly represented by either a rating curve, rule curve, or scheduled release curve. These curves will usually be used in conjunction with a lake polygon to accurately reflect a flow control device. There may be more than one curve type present, but only one of each curve type is allowed at a node. The button for adding a curve type is dimmed out when a curve of that type has been added.

  • Rating curve - piece-wise set of linear stage versus discharge values
  • Rule curve - step-wise set of stage versus discharge values
  • Scheduled release - step-wise set of time versus discharge values

Parameters: table of values representing the curve entered in the XY series editor

Pipe Junction

Data required for modeling storm/tile drain systems is entered at pipe junction nodes.

Super Junction Number

The super junction number is computed by WMS by using the GSSHA | Number Storm Drain menu command in the 2D Grid Module, but can also be manually edited at any time.

Invert Elevation

Enter the invert elevation (m) of the pipe at this location.

Manhole Area

Enter the manhole area (m^2).

Inlet Type

The inlet type is used to account for flow into or out of the pipe network. Select 0-9 grate inlets to specify the amount of flow into the pipe network. Choose Empty to grid cell or Empty to channel to indicate that flow from the pipe network will be routed either back to the grid cell or into the 1-D stream network.

Hydrograph Output

In addition to writing the hydrograph for the outlet cell location to the .otl file, GSSHA can output hydrographs at specific nodes to the .ohl file. Toggle on this option to tell GSSHA to output a hydrograph at this location.

Sediment Output

If the Soil erosion option is selected in the GSSHA Job Control, then this option can be used to tell GSSHA to output the sediment load versus time at this location to the .osl file.

Groundwater BC

Choose one of the following groundwater boundary conditions for modeling groundwater interaction: Generic, Constant Head, Static Well, or Dynamic Well.

Pump Rate

The static well option requires a daily pump rate (m^3/day) and the dynamic well option uses a time varying pump rate entered in the XY series editor by clicking on the Pump rate button.

Solution Results

Click on this button to visualize grid or link/node data sets for this node.

Observations

Click on this button to access the GSSHA Observations dialog and compare observed data to results simulated by GSSHA. This can be helpful for calibrating a GSSHA model.

Related Topics