SMS:Bugfixes SMS 11.1

From XMS Wiki
Jump to: navigation, search


The SMS Intermediate Release Bugfixes page for SMS 11.1.

SMS 11.1 Release Bugfixes

The following bugs have been fixed in this version:

SMS 11.1.19 - Release October 3, 2014

  • 7472 Reading a BOUSS2D simulation results in a bad damping cellstring
  • 7433 Reproject all Does Not Change Display Projection
  • 7428 If a New Project is Read in, The Projection is set before the old data is check on or cleared out
  • 7439 Projection not set with "extra.h5" file when it should be

SMS 11.1.18 - Release September 8, 2014

This is a version release for SMS 11.1

  • 7280 Fixed a Time Series Issue
  • 7366 SMS doesn't read the files associated with a B2D Project quite right
  • 7375 Zoom to selection does not function as expected
  • 7398 Merge meshes results in bad mesh


SMS 11.1.17 - Release July 17, 2014

This is a version release for SMS 11.1

  • 7144 - Fixed ADCIRC elevation forcing time interval
  • 7194 - Fixed Scatter->Mesh Activity not mapped
  • 7195 - Fixed a Resample timestep error
  • 7174 - Fixed Interpolating CGrid vector data to scatter
  • 7183 - Fixed an issue where Can't open large PTM .h5 file

SMS 11.1.16 - Release May 30, 2014

This is a version release for SMS 11.1

  1. Fixed a problem where Saving CMS-Wave Project Incomplete
  2. Fixed a problem with Mesh -> Scatter Crash
  3. Fixed a Problem with cell-by-cell activity in TUFLOW
  4. Fixed a problem where CMS-WAVE Telescoping Grid Unable to Read Vector Data
  5. Fixed a problem where Static Image not linked to the project file
  6. Fixed a problem where Contour label options are always labeled as meters

SMS 11.1.15 - Release April 26, 2014

This is a version release for SMS 11.1

  1. Fixed a Problem where ADH Load Solution From Model Wrapper Was Not Working
  2. Fixed a Problem where USE_AVALANCHING was being written twice in CMS-FLOW cmcards file
  3. Fixed a Problem where SMS writes out wrong TUFLOW card
  4. Fixed Errors importing native TUFLOW simulation
  5. Fixed Prompt to update to version that doesn't exist
  6. Fixed Crash opening project
  7. Fixed a Problem where Dataset Toolbox gives inconsistent values of "NULL" so contours don't process correctly
  8. Fixed a Problem where Null value/Inactivity array - save null value in h5 for each dataset
  9. Fixed a Problem where Null value/Inactivity array - read inactivity array from h5 for each dataset
  10. Fixed a Problem where Null value/Inactivity array - display contours of CGRIDS using NullVal or InactArray
  11. Fixed a Problem where Null value/Inactivity array - display contours of Scatter using NullVal or InactArray
  12. Fixed a Problem where Null value/Inactivity array - display contours of Mesh using NullVal or InactArray
  13. Fixed a Problem where Null value/Inactivity array - convert scatter to mesh with correct NullVal or InactArray
  14. Fixed a Problem where Null value/Inactivity array - identify inconsistencies in NullVal or InactArray between Map and Filter in toolbox
  15. Fixed a Problem where Null value/Inactivity array - set data range correctly when reading XYZ file
  16. Fixed Active/Inactive Cells for TUFLOW
  17. Fixed TUFLOW Active/Inactive Cell Display Confusion
  18. Fixed Initial text in cursor tracking window
  19. Fixed ADCIRC nodestring BC crash
  20. Fixed Crash performing mesh->scatter

SMS 11.1.14 - Release March 25, 2014

This is a version release for SMS 11.1

  1. Fixed an Error Reading ADCIRC fort.22 file
  2. Fixed an Error where "Unable to Find Expected Solution Components" After Running CMS-FLOW

SMS 11.1.12 - Release January 16, 2014

This is a version release for SMS 11.1

  1. Fixed Select/Delete data not selecting cartesian grid cells
  2. Fixed an issue where STWAVE spectral parameters are not stored with the project
  3. Fixed an issue where Spectral Energy dialog does not import/export STWAVE formatted spectra (eng) file for latest version
  4. Fixed an issue where Display Transparency Ctrl does not work for Vtk Mesh
  5. Fixed CGWAVE Trans Error
  6. Fixed Dataset Calculator crash
  7. Fixed an issue where Exporting STWAVE files causes disconnect with the project files and folders
  8. Fixed Errors reading in an ADH project
  9. Fixed an issue where CAD->Map creates duplicate nodes
  10. Fixed an issue where SMS loads a solution when it shouldn't and dataset is wrong
  11. Fixed an issue where LTFATE to map and toggling grid display broke
  12. Fixed an issue where SMS doesn't read in TUFLOW solution file into the correct projection.
  13. Fixed an issue where DMI tables exporting even though disabled.
  14. Fixed an issue where DMI CMS-FLOW Dependency Not Working
  15. Fixed an issue where Loading SRH Files causes SMS to Crash


SMS 11.1.11 - Release December 15, 2013

This is a version release for SMS 11.1

  1. Fixed PTM grid datasets not populating concentration
  2. Fixed an issue causing the .sms project file saves out a reference to the orginal .sms -- meaning when you go to load the new one, it also loads old.
  3. Fixed an issue causing the SRH model parameters to not be saved in the SMS project
  4. Fixed an issue causing Merging nodestrings not functioning as expected
  5. Fixed an issue causing Map->2D Mesh hang
  6. Fixed an issue causing Zonal Classification Crash
  7. Fixed an issue of being unable to extract CMS BC
  8. Fixed an issue causing Error assigning Manning's n for TUFLOW simulations
  9. Fixed an issue causing Time Series plot in SMS with some observation points missing and some duplicated
  10. Fixed an issue causing Select nodes hang
  11. Fixed an issue of CMS Steering not read in the output files after a run.
  12. Fixed an issue causing DMI tables being exported even though disabled.


SMS 11.1.10 - Release November 7, 2013

This is a version release for SMS 11.1

The following bugs have been fixed in this version.

  1. Fixed an issue causing a failure to read in Cgrid datasets.
  2. Fixed an issue causing the CGWAVE Model Control Long wave toolbox to not use specific periods.
  3. Fixed an issue causing the hardbottom dataset to not save out with the project.
  4. Fixed an issue causing multiple .LAS files to be read in when only selecting a single file.
  5. Fixed an issue causing the BOUSS2D parameters to not manage consistently and causing the .spf file not to write out.
  6. Fixed a crash caused by only registering BOUSS2D license and trying to read in an .h5 file.
  7. Fixed a crash caused by performing Map->2D Mesh feature.
  8. Fixed an issue causing the Map->Mesh feature to leave elements outside ofthe domain.
  9. Updated the way SMS handles extreme zoom levels with vectors enabled.
  10. Fixed an issue causing CMS-FLOW models to not write out the bottom friction.
  11. Resolved an issue causing nodestring labels to get visibility settings from 'Mulitple assigned' option when not necessary.

SMS 11.1.9 - Release October 7, 2013

This is a version release for SMS 11.1

  1. Fixed an issue causing mesh subset editing to leave scalar dataset values.
  2. Fixed an issue causing Tidal database access from CMS-Flow to not use time specific variables.
  3. Fixed an issue causing TUFLOW check files projection information to not export for the ArcGIS format.
  4. Fixed an issue causing a set view to display incorrectly after changing timesteps while having vectors displayed.
  5. Resolved an issue resulting in the failure to read an ADCIRC control file with the ADCIRC/SWAN coupling specified.
  6. Fixed an issue relating to ADCIRC spatial attribute (fort.13) files to now read in correctly.
  7. Fixed an issue causing Mesh data to not be saved out with certain projects.
  8. Resolved a crash relating to the ADCIRC Spatial Attributes window.
  9. Fixed an issue causing B2D Wave Maker condition to handle Irregular waves from the file incorrectly.
  10. Resolved an issue preventing the ability to interpolate a raster to mesh.
  11. Fixed an issue causing the conversion of a telescoping grid to not handle all levels of the grid.
  12. Fixed an issue causing the oblique display of functional surfaces to frame incorrectly.
  13. Resolved an issue causing the text in Scalar to Vector dialog to cease updating after switching data set types multiple times.
  14. Resolved an issue causing STWAVE simulation projects to lose the links to spectra in its cases.
  15. Fixed an issue causing BOUSS2D grids to not contour the first cell.
  16. Fixed an issue causing Land Cells to be contoured in CMS-FLOW non-telescoping grids.

SMS 11.1.8 - Release September 5, 2013

This is a version release for SMS 11.1

  1. Resolved an issue causing SMS to freeze when moving a TUFLOW component.
  2. Fixed a crash caused by editing multiple TUFLOW BC coverage arcs at the same time.
  3. Fixed an issue causing SMS to freeze if the user selected an invalid STWAVE surge dataset.
  4. Fixed an issue causing the WAM model to output bad files.
  5. Fixed an issue causing SMS to hang onto specific xmdf.sup files even after the project was closed.
  6. Resolved an issue causing the constant wind STWAVE option to have no effect on the model.
  7. Fixed a crash resulting from converting a Map -> 2D Mesh in 64 bit versions.
  8. Fixed projection issues relating to TUFLOW projects -- changing project will now change the default measurement type.
  9. Fixed an issue causing extracted ADCRIC tidal constituents to not maintain their proper sequencing.
  10. Resolved an issue that resulted in inaccurate number of CGRID cells to be reported.
  11. Fixed an issue causing SMS to hang after adding a scatter point to a corrupt TIN file.
  12. Resolved an error while reading in shapefiles.
  13. Fixed a crash caused while using the TUFLOW CSDB->Cov feature.
  14. Resolved plotting issues that were causing the Plot to not display all defined curves.

SMS 11.1.7 - Release August 5, 2013

This is a version release for SMS 11.1

  1. Fixed an issue causing breaklines to merge incorrectly.
  2. Fixed an issue causing the 'CsDb -> Cov' button in the 'CsDb Management' window to not function properly.
  3. Fixed an issue causing an error while writing un-layered FC Shapes to the .tgc file.
  4. Fixed an issue causing SMS to not pave correctly if the working projection is in Geographic space, also fixed a crash that occurred when mapping to mesh.
  5. Fixed an issue causing a crash while previewing a Mesh in the '2D Mesh Polygon Properties' window.
  6. Fixed a crash caused by processing boundary triangles.
  7. Updated the generic model checker to give complete boundary condition messages.
  8. Resolved an issue preventing users from deleting the AdH Hotstart folder and datasets.
  9. Fixed an issue causing a crash as a result of reading in Curvilinear grids written by SMS after reading from LTFATE files.
  10. Fixed an issue causing Cartesian Grid data to appear distorted and at time, to not read in at all.
  11. Fixed a crash caused from reading in LTFATE .dat files.
  12. Resolved issues causing the Observation Profile Wizard to not work properly with 1D-2D.
  13. Fixed an issue causing duplicate scatter set GUID errors when saving SMS projects which would result in a permanent loss of scatter set elevation data.
  14. Fixed issues relating to the conversion of Vectors to Scalars for telescoping grids.
  15. Fixed an issue causing TUFLOW interface to write out inconsistent .mid & .mif files.
  16. Resolved an issue causing 'Map -> 2D Mesh' feature to have too great of a tolerance -- resulting in bad meshes.
  17. Fixed an issue causing ADCIRC Prep to fail if the directory path was too long.
  18. Fixed a crash caused by loading an ADH Solution file.
  19. Resolved an issue causing the display of the background image to shift when creating flow trace animations.
  20. Fixed an issue causing the 'Nodestring Renumber' feature to be unavailable unless a nodestring was selected.

SMS 11.1.6 - Release July 8, 2013

This is a version release for SMS 11.1

  1. Fixed a problem relating to importing incomplete shape files.
  2. Fixed an issue causing the mesh to remain in the display after being deleted.
  3. Fixed an issue causing the spectral generator to not generate the same spectra values from different directions.
  4. Fixed an issue causing errors to occur while reading in Scatter sets.
  5. Fixed an issue causing contours on a CMS-Flow telescoping grid to be displayed with 'steps' where it used to appear smoothly.
  6. Resolved an issue causing PADCIRC not to run in certain projects.
  7. Fixed an issue that was preventing STWAVE from running.
  8. Resolved a crash resulting from changing the position of the scatter set in the project explorer.
  9. Fixed an issue causing bathymetry interpolation to not give accurate results.
  10. Resolved issues causing vectors on a grid to appear differently when printed than it did on screen.
  11. Fixed a crash caused from converting Map -> 2D Mesh.
  12. Resolved a crash in ADCIRC spatial attributes dialog.
  13. Fixed a crash caused from moving a mesh node.
  14. Resolved issues with the ADH Model Control Checker resulting in reports that Output Times were not being assigned.

SMS 11.1.5 - Release May 30, 2013

This is a version release for SMS 11.1

  1. Fixed a crash caused by the use of spaces in CGWAVE Trans Program.
  2. Fixed an issue causing the time to not be updated in an ADCIRC fort.22 file.
  3. Resolved an issue that caused File|Save for scattersets not to work with certain registrations.
  4. Fixed an issue causing a valid scatter triangle to be reported as invalid.
  5. Resolved an issue causing error messages to pop up while opening FESWMS projects.
  6. Fixed texture mapping issues.
  7. ADCIRC tidal conditions values will now save when leaving the dialog.
  8. Resolved an issue regarding CMS-Wave solution files to not open properly.
  9. Resolved a problem that was stopping users from setting an MPIEXE location.
  10. Fixed a crash caused by Refine Elements option.
  11. Fixed an issue causing .wav files saved in SMS 11.0 to not read into SMS 11.1.
  12. Fixed an issue causing ASCII output files to not be read in after an STWAVE run.
  13. Fixed a crash caused by spectral data with an NaN value.
  14. Resolved an issue causing a polygon select data dialog to not react to user input.
  15. Resolved an issue causing CMS-WAVE to run more cases than were present.
  16. Resolved an issue causing CMS-WAVE solutions to write out incorrect output data.
  17. Fixed an issue causing CMS-FLOW harmonic bc to not be restored.
  18. Fixed an issue that was stopping the user from converting from a mesh to a VTK mesh due to unsupported element types.
  19. Fixed a crash caused by deleting nodes in a mesh.
  20. Resolved an issue causing CMS-FLOW executable to not run correctly.
  21. Fixed a problem causing STWAVE .sim files to not write out correctly.
  22. Updated the CMS-FLOW Model Checker dialog to give the user accurate information.
  23. Resolved an issue with CMS-FLOW flux calculation to now create accurate data.
  24. Fixed an issue with tabbing across spreadsheets within the Cross Sections dialog.
  25. Fixed an issue causing the Extracted BC Dialog window to only get larger after resizing the window.
  26. Fixed an issue causing the GenCade Breakwater data to disappear when the data was not active.
  27. Fixed an issue causing BOUSS2D .eta and .uv files to not read in.
  28. Resolved an issue causing CMS-FLOW projects to change cell values from 999 to -999 after they were unselected or saved out.

SMS 11.1.4 - Release April 25, 2013

This is a version release for SMS 11.1

  1. Resolved an issue allowing the user to only change plot datasets once.
  2. Fixed an issue causing STWAVE to error out upon running.
  3. Fixed an issue causing Pre-ADH to fail if material is defined but not in the mesh.
  4. Fixed an issue causing STWAVE results to be displayed incorrectly.
  5. Resolved an issue that caused SMS to hang while cleaning a coverage.
  6. Resolved issues causing the reading in of Curvilinear grids to take much longer than before.
  7. Resolved an issue causing nodestrings to not have the ability to be merged.
  8. Fixed an issue causing 'Define Domain' command to not be present in CGWAVE coverage.
  9. Fixed an issue causing coverages not have the ability to be deleted.
  10. Resolved an issue causing 'Process Boundary Triangles' to not be visible.
  11. Resolved an issue causing vectors to pull data from the wrong scalar sets.
  12. Fixed an issue causing Line Properties to not save or plot correctly.
  13. Fixed an issue causing a 5th line to not be visible in the Cross Sections Attributes chart.
  14. Resolved issues related to the CMS-Flow dynamic dialog.
  15. Fixed an issue causing CMS-Flow solutions to not be read in after model runs.
  16. Resolved an issue causing the selection of triangles to not work properly if zoomed in too closely.
  17. Fixed an issue causing a crash to occur after displaying vectors on a grid.

SMS 11.1.3 - Beta Release April 5, 2013

This is a bugfix release for SMS 11.1

  1. Updated the output format of CMS-Flow data.
  2. Resolved an issue that was causing errors after a successful STWAVE run.
  3. Fixed a problem that was causing SMS to write out improper TUFLOW 1D-2D connections.
  4. Resolved an issue where vectors were not showing properly after an STWAVE run.
  5. Modified the manner in which CMS-Wave is executed.
  6. Resolved an issue causing older CMS-Flow project to not read in properly.
  7. Resolved an issue causing CMS-Flow grid data to appear inverted.
  8. Fixed Bouss Sim transects to now display correctly.
  9. Fixed a problem relating to Bouss causing SMS to read in one transect multiple times and others not at all.
  10. Fixed an issue causing projection to get transformed twice.
  11. Resolved an issue causing Map on the fly feature to not work for interpolation of CMS-Flow boundary conditions.
  12. Fixed an issue related to the Bouss Probe Rules window upon creating the coverage.
  13. Resolved an issue causing Edit|Select All feature to not work.
  14. Fixed a problem causing the grid to be hidden after merging grid cells.
  15. Fixed a problem causing project on the fly to not work, which resulted in bad values.
  16. Fixed an issue with Active Materials causing the materials to not show up in sub windows.
  17. Updated various CMS-Flow output features.
  18. Resolved a problem causing data ranges on converted spectra to be inaccurate.
  19. Fixed an issue causing display projection to set to Mercator when shapefile with Geographic projection is already loaded.
  20. Resolved an issue causing Bouss2d projects to not read in properly.
  21. Fixed an issue causing CMS-Flow table count dependencies to not update properly after an insert.
  22. Resolved a problem with processing boundary triangles missing some triangles.
  23. Fixed an issue causing a crash while saving out a CMS-Wave file.
  24. Fixed an issue causing a crash while loading an FLT file as a scatter.
  25. Resolved an issue causing the data set to shop up as a 'z' icon rather than a '123' icon after reading in a survey file as a scatter.
  26. Fixed an issue that required an extra click while selecting a data set for interpolation.
  27. Resolved an issue causing Sediment CML information to not be present while dragging .cmcards onto the SMS shortcut.
  28. Updated CMS-Flow observation points to convert to save points.
  29. Fixed a crash caused while saving out an ADCIRC project.
  30. Resolved an issue causing dynamic images to read in as static images after saving and reloading the project.
  31. Resolved multiple related issues with importing ADCIRC files.
  32. Fixed a problem causing SMS to freeze while writing out certain datasets.
  33. Fixed an issue causing SMS to crash upon deleting Particle Data.
  34. Fixed a crash that was caused from 'Feature Objects|Find' command.
  35. Resolved an issue causing TULFOW downstream BC's to not be saved.
  36. Removed 3D coverage functionality from SMS 11.1 as it is not supported.
  37. Fixed an issue where Dynamic tool bars were not being updated after renaming a coverage and changing its type.
  38. Resolved an issue where SMS would not write 2D-2D TUFLOW grid properly.
  39. Fixed a problem causing splitting of a grid row in CMS Wave to distort all bathymetry values before the split line.
  40. Resolved an issue that caused Observation points to be off by one cell value when read into SMS 11.1.
  41. Adjusted the Location column in the Preferences window to take up the full width of the window.

SMS 11.1.2 - Beta Release February 13, 2013

This is a bugfix release for SMS 11.1

  1. Fixed an issue with converting Grids to Maps.
  2. Fixed an issue causing AdH to fail if a material is defined but not in the mesh.
  3. Resolved an issue where loading an RMA2 solution after disabling elements caused the geometry to not match.
  4. Fixed an issue causing the display of scatter sets to not refresh properly.
  5. Fixed an issue causing the FESWMS Model Control BC Descriptor name to not be retained.
  6. Fixed an issue causing an error while reading a wind.in file.
  7. Resolved issues with CMS-FLOW interface and the file formats it writes out.
  8. Fixed an issue with TUFLOW causing the CsDb dialog to not pop up properly.
  9. Resolved a crashing issue with CGWAVE Reset 1D Spacing function.
  10. Resolved an issue with fly reprojection concerning GIS layers.
  11. Resolved an issue with output times not being saved in the AdH Model Control dialog.
  12. Fixed an issue causing CMS Dynamic Datasets to not write out correctly.
  13. Fixed an issue causing SMS to hang while saving a bugged mesh file.
  14. Fixed an issue causing TUFLOW BC Conditions to not be saved.
  15. Fixed an issue where the values in the plot were not matching the values in the dataset.
  16. Fixed an issue where a CMS-FLOW run was trying to read in a file that did not exist.
  17. Resolved an issue where reading in multiple .cmcards files caused the IJ triad to not display in the proper location.
  18. Resolved an issue causing SMS to appear to hang while merging a subset mesh back into a large mesh.

New Features

MIKE 21 (*.mesh) files can now be loaded into SMS 11.1 and later. See the article MIKE 21 *.mesh.

SMS 11.1.1 - Beta Release January 17, 2013

This is a bugfix release for SMS 11.1

  1. Fixed an issue with AdH Model losing data.
  2. Fixed issue related to TUFLOW 1D causing a crash.
  3. Fixed issues related to AdH Sediment Bed Layers tab.
  4. Resolved an issue causing processing boundary triangles to miss some triangles.
  5. Fixed a crash caused from reading in a bad .sol file type.
  6. Fixed a crash related to AdH Nodal Boundary conditions.
  7. Fixed a crash caused by saving out BOUSS2D damping information.
  8. Fixed a crash related to merging scatter sets with delete old sets option.
  9. Resolved a tabbing order issue in the AdH model interface.
  10. Resolved an issue with dragging certain coverages into the TUFLOW simulations.
  11. If a user tries to read in an incomplete .sol file type they will now be notified that it is incomplete.
  12. Resolved an issue where SMS was not writing all necessary .hot information out when saving.

SMS 11.1.1 – Beta Release December 11, 2012

This is a bugfix release for SMS 11.1.0

  1. Resolved issues related to interpolating from rasters or raster sets to scatter sets.
  2. Resolved issue related to the display of contours on a raster (or raster set) as a surface. Scalar values were being offset by half a raster cell.
  3. Added a display state for each raster when the raster is saved to an SMS project so that they are not turned on when the project is loaded.
  4. If a user tries to process boundary triangles when the display projection is not the same projection used by the scatter set will immediately tell the user that the display projection must be changed.
  5. The order of rasters in the list will now control the drawing order. Dragging a raster to a lower position in the raster set will hide that raster behind rasters above it in the list.
  6. Messages related to reading incomplete AdH solutions have been modified to reduce the confusion. Redundant messages have been removed. AdH solution folders are now preserved when a project is saved.
  7. Fixed issue with converted selected map (feature) objects to a scatter set.

Related Topics