User:Jcreer/SRH-2D Error Messages Tables: Difference between revisions

From XMS Wiki
Jump to navigationJump to search
No edit summary
Line 219: Line 219:
| Review the boundary condition arcs and use the snap preview.
| Review the boundary condition arcs and use the snap preview.
|}
|}
 
===Pre-SRH-2D Errors===
This table contains errors that can occur during the PreSRH-2D, or pre-processor, run for the simulation.
{| class="wikitable sortable" style="border:1px solid black;"
{| class="wikitable sortable" style="border:1px solid black;"
|+ Pre-SRH-2D Simulation Errors
|+ Pre-SRH-2D Simulation Errors

Revision as of 20:12, 8 March 2022


SRH-2D Simulation Errors

This table lists errors that are discovered during the SRH-2D simulation run.

SRH-2D Simulation Errors
Location Error Code Error Text from Model Description Potential Solution
SRH-2D 1 Stopped in spline.f90 H Time series data used to define inflows/outflows or time varying water surface elevations has issues with how it is defined, such as duplicate times. The time series data should only have one data value per defined time. Review the XY Series Editor where the time series data is defined for the boundary conditions and remove any duplicate time entries.
SRH-2D 1 Stopped in uti_qwin_xyplot.f90 TIME_SIMU Inconsistent time control settings. The end time is prior to the start time in the model control. Adjust so the end time is later than the start time.
SRH-2D No cells cover an obstruction in structure_obstruction.f90 Obstruction feature area of influence does not cover the centroid of at least one element. The "Obstruction Width/Diameter:" value in the Obstructions Properties dialog is set to "0" and/or an obstruction arc is positioned just beyond half the width/diameter defined in the properties from the centroid of a mesh element.
SRH-2D 5 Stopped in structure_culvert.f90 ICELL error#5 Boundary condition arc mesh snapping does not match inactive material zone snapping. Review the material polygon snapping and review material assignment.
SRH-2D None More than 99 obstructions exist SRH-2D has a built in limit to how many obstructions can be included in a model. Currently this limit is 99. Reduce the number of obstructions to 99 or fewer.
SRH-2D 2 ALL INLET cells are dry from bc_mdot2.f90! Code may have blow up due to input errors or too-large time step. Material polygons near inflow are unassigned. This occurs when the material coverage has not been linked to the simulation. Also occurs when all material polygons covering the inflow BC have an "unassigned" material type. This can also occur if no boundary conditions providing an inflow source have been included in the simulation. Review the simulation to make certain materials have been assigned and that materials and BC coverages have been added to the simulation.
SRH-2D FATAL ERROR The code diverged; further reduction of time step would help the convergence! Too large of a time step. Reduce the size of the computational time step in the model control.
SRH-2D 3 bad mesh ! Stopped in indx_conn.f Problem in mesh, often due to overlapping elements. Check if problem cell (element) id is listed. Otherwise, examine mesh quality in SMS.
SRH-2D 0 Exit code 0 The SRH-2D simulation has stopped or finished whether successfully executed or not. Review the simulation results, if any. Further troubleshooting may be required if there are no solutions data or the data is incomplete.
SRH-2D 8 Inconsistent cell ID in mesh_connectivity: maybe due to wrong nodestring There is an issue with how the BC arcs are being assigned to the mesh elements. Review mesh for overlapping elements. Also, check snapping of BC arcs.
SRH-2D Program Stopped as Mesh is different in RST file

One of the following is different:
Ncell Nvert Nface Nclfc Nclvt in RESTART file
do not match those in the input file
Ncell Nvert Nface Nclfc Nclvt
in restart file are: 13604 7374 20977 41693 41693
in casename.GRD file are: 15459 8277 23735 47225
Mesh topology has to be the same for irest>=1 or init_method=3

Using a restart file that was created with another mesh. Restart files can only be used with simulations using the exact same mesh. Review the restart file and use a restart that matches the mesh. Regenerate the restart file if needed or select a different initial condition option.
SRH-2D 6940 None The assigned material types for the areas upstream or downstream of the culvert location are not valid. Ensure that areas upstream of the upstream culvert location and areas downstream of the downstream culvert location have a valid material type assigned.
SRH-2D 1 Stopped in structure_pressure_flow.f90 PARA DISTANCE Shape of pressure zone is not acceptable for a parabolic type bridge ceiling. Ensure that the pressure zone, between the pressure flow arcs, is rectangular in shape.
SRH-2D 9669 Program stopped due to the following:

Wrong IFACE matching occurred in structure_internal.f90 #4 Error Code is: 9669

The area between the pressure zone arcs with overtopping turned on is not rectangular in shape and/or that the elements in-between the arcs are not rectangular. Ensure that the area between the pressure zone arcs with overtopping turned on is rectangular in shape and that the elements in between the arcs are quads (rectangles). If necessary, create a new mesh with a rectangle between pressure flow arcs and which has quads in this area using the patch mesh generation method.
SRH-2D 46631 Program stopped due to the following:

Wrong IFACE matching occurred in structure_internal.f90 #4 Error Code is: 46631

Ensure that the area between the pressure zone arcs with overtopping turned on is rectangular in shape and that the elements in between the arcs are quads (rectangles). Create a new mesh with a rectangle between pressure flow arcs and which has quads in this area using the patch mesh generation method.
SRH-2D 0 Program stopped due to the following:

Wrong IFACE matching occurred in structure_internal.f90 #4 Error Code is: 0

There is an issue with one or more boundary condition arc definitions. Review snap preview of boundary condition arcs.
SRH-2D 16026 Program stopped due to the following:

A downstream Structure nodestring has not set right; structure_culvert.f90 ICELL error#2 Error Code is: 16026

The 2D mesh around and through the structure is not optimal. Examine the areas around the structure. Suggestions to optimize the mesh around the structure include creating patched (quadrilateral) elements through the structure from one face to the other.
SRH-2D 79 Program stopped due to the following:

Tailwater WSE exceeded the maximum TW in the Reverse HY8 Table structure_hy8.f90 Error Code is: 79

Computed water surface elevations near the culvert became extremely high. This could be from too large of a time step, poor mesh quality near the culvert faces, or parts of the mesh were the culvert is applied have higher elevations than what are defined as the inverts defined in the HY-8 culvert definition Review mesh quality near the culvert face. Check to ensure that mesh node elevations where culvert faces are applied do not exceed invert elevations as defined in the HY-8 culvert definition. Lowering the time step to improve stability around the culvert could also help.
SRH-2D N/A forrtl: severe (24): end-of-file during read, unit n, file {your filepath.dat} Image PC Routine Line Source srh2d_3.2_quickwi...Unknown... This is usually a generic error indicating something is wrong with the SRH-2D simulation casename.DAT file created by SRH pre. It typically signifies that SRH-Pre did not terminate normally and generate a valid simulation file. The cause of the error could be any number of issues. Check for any error messages reported by SRH-pre by going to the SMS model wrapper and clicking on the "PreSRH-2D" line and reviewing the on screen output messages.
SRH-2D N/A Failed to find a mesh cell which contains the following (x y) points: (X,Y)= This is caused when there is a void added to the mesh by deleting a mesh element from the mesh after the mesh has been generated. Creating void by deleting mesh elements may not actually remove the element data from the mesh in SRH-2D. If a void is needed in the mesh, it should be created as a polygon in the Mesh Generator coverage and given a mesh type of "None". When a mesh is generated using polygons with the "None" type, a void will be created in the mesh that can be recognized by SRH-2D.
SRH-2D 0 Program stopped due to the following: IFACE match does not found in structure_culvert.f90 #n Element configuration around the structure face is causing a mismatch in the transition into or out of the structure. It may help to ensure all elements within the two structures are quadrilateral elements. It may also help to ensure that the first row of elements downstream of the downstream structure face and upstream of the upstream structure face are also quadrilateral elements that are "well formed" ("Well formed" elements as in having interior corners as close to 90 degrees as possible).
SRH-2D 1 Program stopped due to the following: Stopped in read_input2.f90 HY8 Forward_TABLE Line Error There is a problem reading the culvert table file. One of the causes of this is that the HY-8 file containing the culvert definition does not include a file extension. Add a ".hy8" file extension to the culvert definition filename.
SRH-2D N/A forrtl: severe (170): Program Exception - stack overflow The simulation is too large for SRH-2D to process. Typically this occurs when running a simulation using sediment transport and a 2D mesh that contains more than 50,000 elements. Reduce the number of elements in the 2D mesh and try running the simulation again.
SRH-2D 3 Not ready in solve.f90 SEDIMENT MODULE This errors occurs when sediment transport is being modeled in a project containing 1D hydraulic structures (culverts, weirs, pressure bridges, etc.). SRH-2D cannot model sediment transport in models containing 1D hydraulic structures. Either do not use the sediment transport in the model run, or remove the 1D hydraulic structures from the model.
SRH-2D 1 Program stopped due to the following: Wrong Boundary ID;may due to some boundary mesh points are not in NODESTRING lists in SMS This error seems to be related to issues with mesh quality. Review mesh quality. Check for elements with very small or very large interior angles (angles less than 10 degrees or greater than 180 degrees. If any are present, make adjustments in the conceptual model (mesh generator coverage) and re-generate the mesh.
SRH-2D 67 Input statement requires too much data, unit 1 This error appears related to using a restart file that doesn't match the project geometry. Review the restart file. Common issues appear to be using a restart file that came from a different project or uses a different projection. Check that all major aspects of the project geometry (mesh, nodes, units, coordinate system) match what is used in the project in order to use a restart file. The other solution is to not use a restart file with the simulation and select another option for the initial condition.
SRH-2D 7 Inconsistant cell ID in mesh_connectivity.f90: maybe wrong nodestring This error is caused when two arcs in the boundary condition coverage snap to the same nodes but have different boundary condition types. Review the boundary condition arcs and use the snap preview.

Pre-SRH-2D Errors

This table contains errors that can occur during the PreSRH-2D, or pre-processor, run for the simulation.

Pre-SRH-2D Simulation Errors
Location Error Code Error Text from Model Description Potential Solution
PreSRH-2D 1 unable to open srhhydro file! Unable to open the exported srhhydro file. The path length for the SMS project is too long. Therefore, the SRH-2D preprocessor could not read the exported files from SMS. Reduce the path length to less than 300 characters.
PreSRH-2D 1 Element ID is not consecutive The mesh element ID's have been mismatched since some mesh nodes were modified and not renumbered. Renumber the mesh nodes using the Renumber command under the Nodes menu in the Mesh module. Pre SRH-2D Errors from final_touch.f90 **** on MONITOR LINE#n
a face cannot be found given two mesh points

Two points are: xx xx
Check the mesh node list; do this using _SIF.dat file directly!

Monitor line spans a void or hole in the mesh. Reconfigure the monitor line. Monitor lines cannot span holes in the mesh.
PreSRH-2D 157 forrtl: severe (157): Program Exception - access violation SMS failed to locate the SRH-Pre executable. Review the file location in the Preferences dialog to ensure it is set to the correct location for SRH-Pre.
PreSRH-2D MESH-UNIT: Enter one of the following options for the unit of the mesh. There is an issue with the units set for the project. SRH requires that vertical and horizontal units be in either meters or U.S survey feet. Review the project and mesh project and units.