GMS:LPF Package

From XMS Wiki
(Redirected from GMS:MODFLOW LPF Package)
Jump to navigationJump to search
MODFLOW
Pre-processing
MODFLOW Commands
Building a MODFLOW Model
Map to MODFLOW
Calibration
Packages Supported in GMS
Saving a MODFLOW Simulation
Importing MODFLOW Files
Unsupported MODFLOW Features
Run MODFLOW
Post-processing
MODFLOW Display Options
MODFLOW Post-Processing Viewing Options
Reading a MODFLOW Simulation
Tutorials
Packages
Flow: BCF6, HUF, LPF, UPW
Solvers:

DE4, GMG, NWT, PCG,

PCGN, LMG, SIP, SOR,

SMS
Other:

BAS6, BFH, CHD1, CLN,

DRN1, DRT1, EVT1, ETS1,

GAGE, GHB1, GNC, HFB1,

HUF, LAK3, MNW1, MNW2,

OUT1, RCH1, RIV1, SFR2,

STR1, SUB1, SWI2, WEL1,

UZF1

The Layer-Property Flow (LPF) package is an alternative to the BCF and HUF packages and is similar to the "true layer" option used with the BCF package in version 3.1. With MODFLOW 2000, the layer elevations (top and bottom) are defined as input to the Global Process (using the Global Options dialog), regardless of which flow package is being used. With the LPF package, define the horizontal (Kh or HK) and vertical hydraulic conductivity (Kv or VK) for each layer. MODFLOW then computes the cell by cell conductances using the K values and the layer geometry.

Other noteworthy features include the ability to enter horizontal anisotropy values on a cell by cell basis. There is also an option to specify vertical anisotropy factors rather than vertical hydraulic conductivity values. This option is particularly useful when performing automated parameter estimation since it ties the Kv to Kh and eliminates the need to define Kv as an independent parameter.

Another feature of the LPF package relative to the BCF package is that there are now only two layer types: confined and convertible. A convertible layer is similar to the LAYCON = 2 and LAYCON = 3 types in the BCF package. The layer can be either confined or unconfined depending on the elevation of the computed water table.

Once the LPF package has been chosen using the packages dialog, the LPF package dialog can be accessed through the LPF – Layer Property Flow command in the MODFLOW menu.

The LPF Package dialog.

Use data arrays

This option allows entering conductivities on a layer-by-layer basis. When this option is chosen, the Horizontal Hyd. Conductivity, Vertical Hyd. Conductivity, Specific Storage, etc. buttons will be available.

Use material ids

This options uses material sets in the place of property arrays. Property values are entered on a material-by-material basis. When MODFLOW files are saved, GMS internally replaces the correct values from the materials to the property arrays. When this option is chose, the property array buttons are replaced with the Material Properties and Material IDs buttons.

Layer

This field displays the current layer. Selecting any of the input array buttons will display the corresponding layer initially. For multiple layer models, this field can be incremented or decremented to show other layers.

Layer type

This radio group selects the layer type for the current layer. There are four options, Confined, Convertible, Convertible Negative, and Convertible Upstream. By default, all layers are convertible (where the layer can be either confined or unconfined depending on the elevation of the computed water table). Here layer type can be changed to confined. Only one layer type can be assigned to each grid layer.

Vertical hydraulic conductivity

The LPF package has the option to enter vertical hydraulic conductivity values as either actual hydraulic conductivity values or as anisotropy factors dependant on horizontal hydraulic conductivity. Vertical anisotropy (VKA) "is the ratio of horizontal to vertical hydraulic conductivity. In this case, HK is divided by VKA to obtain VK, and values of VKA typically are greater than or equal to 1.0."[1] These options are only available for multi-layer models.

Interblock transmissivity

The method used for computing interblock transmissivity is specified using the pull-down list in the middle right portion of the LPF Package dialog.

Layer Data Arrays

The seven buttons in the middle-right portion of the dialog represent layer data arrays such as elevations and hydraulic conductivity. Each of the seven buttons brings up the MODFLOW Array Editor. Not all of the data arrays need to be specified for each layer. Some arrays such as Specific Storage and Specific Yield are only required for transient models.

Cell Wetting Parameters

If re-wetting of cells (when cells that went dry during the simulation later have head) is allowed, a wetting factor, wetting iteration interval, and wetting equation must be specified.

More LPF Options

Clicking on the More LPF Options button brings up the LPF Package Options dialog where it is possible to remove vertical leakance correction or set a head value for dry cells.

The LPF Package Options dialog.

Remove vertical leakance correction

This is the value that MODFLOW will give to cells with a head level below the bottom elevation of the cell (dry cell). When reading in a solution, GMS will mark cells with this value with a dry cell symbol. The Layer Property Flow Package of MODFLOW-2000 was modified by A.W. Harbaugh (U.S. Geological Survey, written commun., 2002) to remove the vertical leakage correction for conditions in which a partially saturated cell is immediately below a fully or partially saturated cell (Harbaugh and others, 2000, p. 31-33). The vertical leakage correction simulates perched conditions within an aquifer system. However, perched conditions are not known to be widespread on a basin scale. The vertical leakage correction adds an additional nonlinear term to the model (A.W. Harbaugh, U.S. Geological Survey, written commun., 2002), which resulted in several of the numerical solvers (SIP (strongly implicit procedures), SOR (slice-successive overrelaxation), and PCG (Hill, 1990; Harbaugh and others, 2000) not coming to a solution and the LMG (link-algebraic multigrid; Mehl and Hill,2001) solver providing unacceptable volumetric budget errors (wrir02-4200.pdf) . Thus in the LPF package there is the option to turn off the vertical leakance correction to account for these factors. After turning on the Remove Vertical Leakance Correction toggle, GMS then uses the NOCVCORRCTION option that is found in MODFLOW2005 to remove vertical leakance corrections.

Head Assigned to Dry Cells

This is the value that MODFLOW will give to cells with a head level below the bottom elevation of the cell (dry cell). When reading in a solution, GMS will mark cells with this value with a dry cell symbol.

Notes