SMS:Grid Frame Properties: Difference between revisions

From XMS Wiki
Jump to navigationJump to search
No edit summary
No edit summary
Line 40: Line 40:
Depending on the application of the grid frame, it will have a variety of attributes or properties.
Depending on the application of the grid frame, it will have a variety of attributes or properties.


The user can interact with the grid frame interactively when the '''Select Grid Frame''' tool is active, or define grid frame properties explicitly using the ''Grid Frame Properties'' dialog (this dialog is accessible by right clicking on the grid frame or when converting to a grid.
The user can interact with the grid frame interactively when the '''Select Grid Frame''' tool is active, or define grid frame properties explicitly using the ''Grid Frame Properties'' dialog (this dialog is accessible by right-clicking on the grid frame or when converting to a grid.


==1D Grid Frame Properties==
==1D Grid Frame Properties==

Revision as of 16:38, 9 December 2014


The Grid Frame Properties dialog is accessed when the Create 1D Grid Frame tool or the Create 2D Grid Frame tool is used. It can also be accessed after a grid frame has been created by using Select 1D Grid Frame tool or the Select 2D Grid Frame tool then right-clicking on the grid and selecting the Properties command from the right-click menu.

The Grid Frame Properties dialog allows the user to specify the attributes applied to the grid frame when performing a Map → 2D Grid operation. These properties are as follows:

  • Origin X/Y – Set the bottom left corner location of the grid frame.
  • Orientation
  • Angle – Set the angle the grid frame will be rotated counter-clockwise from the +x axis.
  • I/J size – Set the length and width of the grid frame. The Cell Dimensions are updated: Cell X = Grid X / Number of Columns, Cell Y = Grid Y / Number of Rows.
  • Cell Options – These options vary based on the grid type being generated. A few of the options are illustrated below. The user specifies the size of the cells to be created in each of the applicable directions from the following options:
  • Cell size (or Base cell size if telescoping is an option) – Set the dimension (width or height) of each cell for the grid to be created.
  • Number of cells – Set the number of rows and/or columns for the grid to be created.
  • Use refine points – Tell SMS to use specified refine points in a CMS-Flow or CMS-Wave coverage. This will result in rectangular cells with variable aspect ratio.
    • Maximum cell size – the max size the should exists when growing
    • Maximum bias – the max growth ratio to be used when growing
    • Use inner growth – specifies whether the cell sizes should grow between two refine points
  • Grid size – the grid dimension in the specified direction
  • Adjust base cell size – This button appears only for CMS-Flow coverages when there are feature polygons with target maximum size guidelines specified. Clicking on this button will update the base cell sizes so that the larger of the two is a multiple of the minimum feature size that is to be represented in the grid. For example, if the user has specified 20 m as the maximum cell size (to allow for 5 cells to represent a channel that is 100 m across), and the base cell size is 75 m in both directions, this button will increase the base cell size to 80 meters in both directions. Therefore the smallest cell generated will be 20 m by 20 m, whereas, a base cell size of 75 m would result in a cell 18.25 m on each side. The objective is to make the base cell size correspond to the smallest user specified target cell size.
  • Options – Set the interpolation options for the Scatter applications. Not used for the Cartesian or 1D Grid applications.

When the user specifies "Define cell sizes", there are a few options available. These options are:

  1. Specify cell size – specify the cell size and the number of cells will be computed.
  2. Specify number of cells – specify the number of cells and the cell size will be computed.

If the grid is to have square cells, the v direction cell size will always be linked to the u direction cell size.

The Grid Frame Properties dialog varies depending on the active coverage.

They are also created temporarily in a number of functions in the SMS interface including:

Grid frames consist of a rectangular shape, normally defined by three graphical clicks, which can be oriented and stretched using handles on the sides and corners as shown in the following image to create an arbitrary rectangle shape.

File:Gridframe.gif

Depending on the application of the grid frame, it will have a variety of attributes or properties.

The user can interact with the grid frame interactively when the Select Grid Frame tool is active, or define grid frame properties explicitly using the Grid Frame Properties dialog (this dialog is accessible by right-clicking on the grid frame or when converting to a grid.

1D Grid Frame Properties

File:1D Grid Frame Properties.jpg
GenCade Grid Frame Properties dialog

2D Grid Frame Properties

File:Grid Frame Properties.jpg
TUFLOW Grid Frame Properties dialog
File:Grid Frame Properties2.jpg
Grid Frame Properties dialog with CMS-Flow coverage

Scater to Grid Conversion Properties

File:Scatter Grid Frame.jpg
Grid Frame dialog using Interp to Scatter Grid command dialog

Related Topics