WMS:Path of Data from WMS To HY8: Difference between revisions

From XMS Wiki
Jump to navigationJump to search
 
(13 intermediate revisions by the same user not shown)
Line 3: Line 3:
The HY8 Modeling Wizard in WMS gathers data to setup an HY8 model.  Some data can be changed at multiple locations, and all variables can be changed in the HY-8 model when the model is setup.  This data is categorized as follows: Discharge Data, Tailwater Data, Roadway Data, Culvert Data, and Site Data. These categories can be seen in the HY-8 interface.
The HY8 Modeling Wizard in WMS gathers data to setup an HY8 model.  Some data can be changed at multiple locations, and all variables can be changed in the HY-8 model when the model is setup.  This data is categorized as follows: Discharge Data, Tailwater Data, Roadway Data, Culvert Data, and Site Data. These categories can be seen in the HY-8 interface.


[[Image:HY8EditCrossing.png|thumb|none|left|600 px|''Crossing Data'' dialog in the HY8 Modeling Wizard.]]
:[[Image:HY8EditCrossing.png|thumb|none|left|600 px|''Crossing Data'' dialog in the HY8 Modeling Wizard.]]
 


==Discharge Data==
==Discharge Data==
This information is pulled from the HY-8 Wizard on step [[WMS:Crossing Discharge Data|Crossing Discharge Data]].
This information is pulled from the HY-8 Wizard on step [[WMS:Crossing Discharge Data|Crossing Discharge Data]].


[[Image:HY8ModelingWizardCrossingDischargeData.png|thumb|none|left|550 px|''Crossing Discharge Data'' dialog in the HY8 Modeling Wizard.]]
:[[Image:HY8ModelingWizardCrossingDischargeData.png|thumb|none|left|550 px|''Crossing Discharge Data'' dialog in the HY8 Modeling Wizard.]]


If the user specifies the flow source as 'Design Flow', the minimum flow value will be zero and the design and maximum flow value will be the value entered by the user.   
If specifying the flow source as "Design Flow", the minimum flow value will be zero. Enter the design and maximum flow value.  
If the user specifies the flow source as 'Hydrograph', the minimum flow in the hydrograph will be the minimum flow value in HY-8, while the maximum flow in the hydrograph will be both the design and maximum flow value in HY-8.   
   
Finally, if the user specifies 'Design Flow & Hydrograph' as the flow source, WMS will use the minimum and maximum flow values from the hydrograph and allow the user to enter the design value.
If specifying the flow source as "Hydrograph", the minimum flow in the hydrograph will be the minimum flow value in HY-8, while the maximum flow in the hydrograph will be both the design and maximum flow value in HY-8.   
 
Finally, if specifying "Design Flow & Hydrograph" as the flow source, WMS will use the minimum and maximum flow values from the hydrograph and allow entering the design value.


==Tailwater Data==
==Tailwater Data==
The information for the tailwater is saved in the tailwater arc.   
The information for the tailwater is saved in the tailwater arc.   


[[Image:HY8ModelingWizardWMSScreenshot.png|450 px]]
:[[Image:HY8ModelingWizardWMSScreenshot.png|450 px]]


The 'Channel Slope' is determined from the slope of the tailwater arc.  The 'Channel Invert Elevation' is initialized with the value of the elevation at upstream end of the tailwater arc.
The "Channel Slope" is determined from the slope of the tailwater arc.  The "Channel Invert Elevation" is initialized with the value of the elevation at upstream end of the tailwater arc.


[[Image:HY8-WMSTailwaterAtts.png|thumb|none|left|900 px|Tailwater ''Attributes'' dialog.]]
:[[Image:HY8-WMSTailwaterAtts.png|thumb|none|left|900 px|Tailwater ''Attributes'' dialog.]]


The 'Channel Type', 'Bottom Width', 'Side Slope', 'Manning's n', 'Constant Tailwater Elevations', 'Irregular Channel Cross-Sections', and 'Rating Curves' are set in the attribute table for the arc.
The "Channel Type", "Bottom Width", "Side Slope", "Manning's n", "Constant Tailwater Elevations", "Irregular Channel Cross-Sections", and "Rating Curves" are set in the attribute table for the arc.


==Roadway Data==
==Roadway Data==


[[Image:HY8ModelingWizardWMSScreenshot.png|450 px]]
:[[Image:HY8ModelingWizardWMSScreenshot.png|450 px]]
 
The length of the roadway, or "Crest Length", is determined from the length of the tailwater arc.


The length of the roadway, or 'Crest Length', is determined from the length of the tailwater arc.
:[[Image:HY8-WMSRoadwayAtts.png|thumb|none|left|700 px|Roadway ''Attributes'' dialog.]]


[[Image:HY8-WMSRoadwayAtts.png|thumb|none|left|700 px|Roadway ''Attributes'' dialog.]]
The "Roadway Surface", "Discharge coefficient", "Roadway Top Width", and "Elevation Profile" are set in the ''Attributes'' dialog for the arc. The elevation profile will set whether the roadway has a constant roadway elevation or if it is an irregular shape.  


The 'Roadway Surface', 'Discharge coefficient', 'Roadway Top Width', and 'Elevation Profile' are set in the ''Attributes'' dialog for the arc. The elevation profile will set whether the roadway has a constant roadway elevation or if it is an irregular shape.  
:[[Image:HY8EditDemElevations.png|thumb|none|left|450 px|''Edit DEM Elevations'' dialog.]]


[[Image:HY8EditDemElevations.png|thumb|none|left|450 px|''Edit DEM Elevations'' dialog.]]
If editing the elevation profile, a plot will appear with a red line and a blue line. The red line represents the elevation of the DEM while the blue line represents the finished roadway elevation.  When clicking '''OK''' on this dialog, WMS will change the DEM under the roadway arc to match the finished roadway.  For this reason, leave one point lower, preferably at the culvert invert elevation, and at the same location as the culvert crossing.  When Topaz determines flow directions and accumulations, the water will be able to route through the roadway at the proper location.  When WMS brings the roadway profile to HY8, it will remove the lowest point and then remove any points that are unnecessary (if there are three or more points with the same elevation, it will remove all but the points at the end of the group that are the same elevation).


If the user clicks to edit the elevation profile, the user will see a plot with a red line and a blue line.  The red line represents the elevation of the DEM while the blue line represents the finished roadway elevation.  When the user clicks okay on this dialog, WMS will change the DEM under the roadway arc to match the finished roadway.  For this reason, the user must leave one point lower, preferably at the culvert invert elevation, and at the same location as the culvert crossing.  When Topaz determines flow directions and accumulations, the water will be able to route through the roadway at the proper location.  When WMS brings the roadway profile to HY8, it will remove the lowest point and then remove any points that are unnecessary (if there are three or more points with the same elevation, it will remove all but the points at the end of the group that are the same elevation).
HY8 requires that the irregular roadway has between 3 and 15 points.  If the profile has two points after removing the lowest and unnecessary points, WMS will assign it to be a constant roadway elevation.  Otherwise it will assign it to be an irregular roadway profile.  If the profile has more than fifteen points, WMS will remove the least significant points until it has only fifteen points remaining.
HY8 requires that the irregular roadway has between 3 and 15 points.  If the profile has 2 points after removing the lowest and unnecessary points, WMS will assign it to be a constant roadway elevation.  Otherwise it will assign it to be an irregular roadway profile.  If the profile has more than 15 points, WMS will remove the least significant points until it has only 15 points remaining.


==Culvert Data==
==Culvert Data==


There is no culvert data that is set in WMS.  The user must enter all culvert data in the HY-8 interface.
There is no culvert data that is set in WMS.  Enter all culvert data in the HY-8 interface.


==Site Data==
==Site Data==
Line 49: Line 51:
Some of the parameters for the site data is saved in the culvert crossing arc and some of the parameters are not changed by WMS.  
Some of the parameters for the site data is saved in the culvert crossing arc and some of the parameters are not changed by WMS.  


[[Image:HY8ModelingWizardWMSScreenshot.png|450 px]]
:[[Image:HY8ModelingWizardWMSScreenshot.png|450 px]]


WMS will take the length of the culvert crossing arc and set the 'Inlet station' to zero and the length to the 'Outlet Station'.  The elevations are then set to the elevations of the DEM at those locations of the culvert crossing arc.  The 'Number of Barrels' and all of the parameters for the 'Embankment Toe Data' option are not handled by the WMS interface and must be updated in the HY-8 interface.
WMS will take the length of the culvert crossing arc and set the "Inlet station" to zero and the length to the "Outlet Station".  The elevations are then set to the elevations of the DEM at those locations of the culvert crossing arc.  The "Number of Barrels" and all of the parameters for the "Embankment Toe Data" option are not handled by the WMS interface and must be updated in the HY-8 interface.


{{WMSHy8ModWizard}}
{{WMSHy8ModWizard}}
Line 57: Line 59:


[[Category:WMS To HY8|P]]
[[Category:WMS To HY8|P]]
[[Category:WMS Dialogs|P]]
[[Category:WMS Modeling Wizard Dialog]]

Latest revision as of 15:01, 20 October 2017

The Path of Data from WMS to HY8 in the HY8 Modeling Wizard

The HY8 Modeling Wizard in WMS gathers data to setup an HY8 model. Some data can be changed at multiple locations, and all variables can be changed in the HY-8 model when the model is setup. This data is categorized as follows: Discharge Data, Tailwater Data, Roadway Data, Culvert Data, and Site Data. These categories can be seen in the HY-8 interface.

Crossing Data dialog in the HY8 Modeling Wizard.

Discharge Data

This information is pulled from the HY-8 Wizard on step Crossing Discharge Data.

Crossing Discharge Data dialog in the HY8 Modeling Wizard.

If specifying the flow source as "Design Flow", the minimum flow value will be zero. Enter the design and maximum flow value.

If specifying the flow source as "Hydrograph", the minimum flow in the hydrograph will be the minimum flow value in HY-8, while the maximum flow in the hydrograph will be both the design and maximum flow value in HY-8.

Finally, if specifying "Design Flow & Hydrograph" as the flow source, WMS will use the minimum and maximum flow values from the hydrograph and allow entering the design value.

Tailwater Data

The information for the tailwater is saved in the tailwater arc.

HY8ModelingWizardWMSScreenshot.png

The "Channel Slope" is determined from the slope of the tailwater arc. The "Channel Invert Elevation" is initialized with the value of the elevation at upstream end of the tailwater arc.

Tailwater Attributes dialog.

The "Channel Type", "Bottom Width", "Side Slope", "Manning's n", "Constant Tailwater Elevations", "Irregular Channel Cross-Sections", and "Rating Curves" are set in the attribute table for the arc.

Roadway Data

HY8ModelingWizardWMSScreenshot.png

The length of the roadway, or "Crest Length", is determined from the length of the tailwater arc.

Roadway Attributes dialog.

The "Roadway Surface", "Discharge coefficient", "Roadway Top Width", and "Elevation Profile" are set in the Attributes dialog for the arc. The elevation profile will set whether the roadway has a constant roadway elevation or if it is an irregular shape.

Edit DEM Elevations dialog.

If editing the elevation profile, a plot will appear with a red line and a blue line. The red line represents the elevation of the DEM while the blue line represents the finished roadway elevation. When clicking OK on this dialog, WMS will change the DEM under the roadway arc to match the finished roadway. For this reason, leave one point lower, preferably at the culvert invert elevation, and at the same location as the culvert crossing. When Topaz determines flow directions and accumulations, the water will be able to route through the roadway at the proper location. When WMS brings the roadway profile to HY8, it will remove the lowest point and then remove any points that are unnecessary (if there are three or more points with the same elevation, it will remove all but the points at the end of the group that are the same elevation).

HY8 requires that the irregular roadway has between 3 and 15 points. If the profile has two points after removing the lowest and unnecessary points, WMS will assign it to be a constant roadway elevation. Otherwise it will assign it to be an irregular roadway profile. If the profile has more than fifteen points, WMS will remove the least significant points until it has only fifteen points remaining.

Culvert Data

There is no culvert data that is set in WMS. Enter all culvert data in the HY-8 interface.

Site Data

Some of the parameters for the site data is saved in the culvert crossing arc and some of the parameters are not changed by WMS.

HY8ModelingWizardWMSScreenshot.png

WMS will take the length of the culvert crossing arc and set the "Inlet station" to zero and the length to the "Outlet Station". The elevations are then set to the elevations of the DEM at those locations of the culvert crossing arc. The "Number of Barrels" and all of the parameters for the "Embankment Toe Data" option are not handled by the WMS interface and must be updated in the HY-8 interface.