GMS:EVT Package: Difference between revisions

From XMS Wiki
Jump to navigationJump to search
No edit summary
Line 37: Line 37:


===2D Data Set -> Array===
===2D Data Set -> Array===
The 2D Data Set -> Array button brings up the Data Browser listing all of the current data sets associated with the current 2D grid. In order for this button to be active, the 2D grid must have the same number of rows and columns as the 3D grid. The selected data set is copied to the recharge array. Data sets are typically generated with the 2D Scatter Point module. The 2D Scatter Point module can be used to interpolate from a scattered set of rainfall measurements to the cell locations. If the data set is transient, the values in the data set are linearly interpolated, if necessary, to each stress period as the data set is copied to the array.
The '''2D Data Set -> Array''' button brings up the Data Browser listing all of the current data sets associated with the current 2D grid. In order for this button to be active, the 2D grid must have the same number of rows and columns as the 3D grid. The selected data set is copied to the recharge array. Data sets are typically generated with the 2D Scatter Point module. The 2D Scatter Point module can be used to interpolate from a scattered set of rainfall measurements to the cell locations. If the data set is transient, the values in the data set are linearly interpolated, if necessary, to each stress period as the data set is copied to the array.


===Array -> 2D Data Set===
===Array -> 2D Data Set===

Revision as of 17:31, 14 May 2012

MODFLOW
Pre-processing
MODFLOW Commands
Building a MODFLOW Model
Map to MODFLOW
Calibration
Packages Supported in GMS
Saving a MODFLOW Simulation
Importing MODFLOW Files
Unsupported MODFLOW Features
Run MODFLOW
Post-processing
MODFLOW Display Options
MODFLOW Post-Processing Viewing Options
Reading a MODFLOW Simulation
Tutorials
Packages
Flow: BCF6, HUF, LPF, UPW
Solvers:

DE4, GMG, NWT, PCG,

PCGN, LMG, SIP, SOR,

SMS
Other:

BAS6, BFH, CHD1, CLN,

DRN1, DRT1, EVT1, ETS1,

GAGE, GHB1, GNC, HFB1,

HUF, LAK3, MNW1, MNW2,

OUT1, RCH1, RIV1, SFR2,

STR1, SUB1, SWI2, WEL1,

UZF1

The Evapotranspiration package is used to simulate the effect of plant transpiration and direct evaporation by removing water from cells during a simulation. Evapotranspiration is typically defined by specifying values for each stress period for each vertical column in the grid. The values consist of an elevation, an ET extinction depth, and a maximum ET rate. The elevation is an absolute elevation and the ET extinction depth (measured positive downward) is relative to the specified elevation. If the water table rises above the specified elevation, the evapotranspiration occurs at the maximum ET rate. If the water table falls below the ET extinction depth, evapotranspiration ceases. If the water table elevation lies between these two extremes, the evapotranspiration rate varies linearly with depth. The ETS package, a later extension of the EVT package, allows the rate to vary non-linearly.

From OFR00-466[1]


To learn more about Evapotranspiration in MODFLOW go here: http://water.usgs.gov/nrp/gwsoftware/modflow2000/ofr00-466.pdf

EVT Package Dialog

The dialog for editing the evapotranspiration package input data is identical to the Recharge Package dialog except that rather than editing the flux and layer indicator arrays, the evapotranspiration arrays are edited: elevation, ET extinction depth, maximum ET rate, and layer indicator.

Evapotranspiration Option

Two ET options are supported by MODFLOW: ET only at the top layer, and ET at specified vertical cells.

Multiplier

The multiplier is a constant which can be written to the package file with each stress period array. Each value in the array is scaled by the multiplier as the array is imported to MODFLOW. The format button brings up a dialog listing the standard MODFLOW formats. This format is used for displaying the values in the spreadsheet and it controls how the values are written to the package file.

Stress Periods

The values displayed in the spreadsheet are for an individual stress period. The values associated with other stress periods can be edited by entering the ID of the desired stress period in the Stress period edit box in the center of the dialog. If the Use previous option is selected for a given stress period, the values from the previous stress period are used and the spreadsheet is dimmed.

2D Data Set -> Array

The 2D Data Set -> Array button brings up the Data Browser listing all of the current data sets associated with the current 2D grid. In order for this button to be active, the 2D grid must have the same number of rows and columns as the 3D grid. The selected data set is copied to the recharge array. Data sets are typically generated with the 2D Scatter Point module. The 2D Scatter Point module can be used to interpolate from a scattered set of rainfall measurements to the cell locations. If the data set is transient, the values in the data set are linearly interpolated, if necessary, to each stress period as the data set is copied to the array.

Array -> 2D Data Set

The Array -> 2D Data Set button copies the array to the 2D data set list associated with the existing 2D grid.

Constant -> Array

The Constant -> Array button brings up a dialog which prompts for a single value. This constant is then assigned to each item in the array for the given stress period.

Spreadsheet

The spreadsheet allows you to edit a 2D array of values, the type depending on the selection in the view/edit combo box. The array types include elevation, et extinction depth, and max ET rate.

Notes